SPS Pumps nv/sa

SPS Project/SKID – Specific services SPS Pumps is the ideal pump distributor because we not only know their pumps, but we also select, configure and if possible “custom-built-to-application” which means that the composing components are adapted to your application instead of working exclusively with standard parts. Due to our ultra-rapid configuration and calculation tools, as

• QUANTUM is a revolutionary solid-block AODD pump made of UPPE or PTFE, with very high chemical resistance and mechanical strength. • Unperforated diaphragms for up to 7x longer lifetime, short pump stroke for less fatigue • Air section on the outside of the pump and fluid section on the inside with change of balls

Motors and geared motors Thanks to our experience and know-how, we are able to select the right motor and gearbox to suit the application and environment, usually with a matching lantern piece to allow the mounting of IEC B5 motors, reducing maintenance times and avoiding dependence on one supplier for motor replacement. In addition, this

These pumps are FDA compliant because all parts in contact with the liquids are made of 316 electropolished 125 Ra or PTFE, materials approved in the food industry. In addition, the pump has an air system with very few unlubricated parts, which means no contamination can occur if the diaphragm ruptures and there are also

Applications: Conveyor fluids; delicate food like sorbet macedoine, diced fruits and vegetable, cosmetic and chemical industries. – No metal to metal contact – Self-priming, reversible, – CIP and transfer with one pump, – Easy to change cartridge seal. – Maximum hygiene, – Two pumps in one, – Low life cycle costs, – Simple maintenance.

Wangen Hyline – design according to EHEDG, 3A and GMP guidelines 45l/h to 3000 l/h at up to 24bar The rotor is connected to the motor via flexible rubber lined coupling, with no recess or awkward edge for the product to accumulate. The pump housing has no dead zone, the product flow is smoother. All

Applications: Suction, feeding, dosing, loading, flushing, transfers, biogas, sewage sludge. – Ideal pump for waste water, – Exceptional reliability of the cardan shaft, – Wide viscosity range, – Good pumping performance even at high pressure. – Pulsation-free pumping with constant flow rate independent of pressure and viscosity, – Constant flow speed in the pump body

Wangen XPress – Heavy duty industrial screw pump for medium viscosity products with ultra low owner cost Wangen screw pumps are designed to facilitate maintenance via the X-lift system, allowing the pump to be serviced in-line. The cardan coupling provides a very robust power transmission without the typical secondary wear of a pin connection used

The WANGEN X-UNIT is used wherever foreign bodies and contaminants have to be separated from the media to be transported and crushed – biogas plants, – reuse of biological waste, – use in stables in agricultural technology, – manure processing technology in vehicle construction, – Municipal sewage treatment plants (water treatment). Consist of 2 units

High capacity industrial peristaltic pumps. Applications: Sewage treatment plants (sludge); Biogas; Fish transfer; Meat, chemical and food industry; Off-shore; Mining. – Tolerates large bodies as long as they are not hard or sharp (risk of tearing the hose), – Extremely low energy consumption (efficientcy of the rollers), – Easy to maintain and simple to clean,

Landia chopper pumps, with their unique external chopping knife system, are designed for pumping heavily contaminated liquids and sludge with high solids concentration. Applications : domestic wastewater with food waste, paper, fat and wet wipes ; abattoir waste water with bones, intestines, feathers, hair and fat ; sludge, organic waste, slurry and straw at biogaz

Grundfos & Landia Mixers for wastewater (water treatment) In addition to our extensive range of wastewater pump solutions, such as chopper pumps, submersible pumps, self-priming pumps,… You can count on a matching mixer solution such as a vertical mixer, horizontal mixer, aeration pump, rotary mixer, … for small to very large tanks. We can provide

Highly accurate chemical dosing pumps for all types of applications: water treatment, chlorine dosing… Smart Digital dosing. – The most efficient on the market (accurate to ±1% in a range of 0.1% to 100% of maximum flow rate) – Easy maintenance and proven reliability – Detection of overpressures (adjustable max pressure) – Dosing line break

Grundfos TP(E) The Grundfos TP(E) is the perfect choice if you have limited space or if you want to be very economical by minimising pipe losses and increasing insulation. As a result, TP(E) pumps are typically used in systems with heat exchangers, although they can also be used in water supply or cooling systems. This

Grundfos CR The CR pump is a very versatile pump for high pressure or booster systems: – It can be connected in series with larger high-pressure pumps – It can be designed as a high pressure pump itself – Available with a VFD and fully automated, state-of-the-art software for remote operation, including by mobile phone

Grundfos NB – Grundfos NK The NK/NB pumps are the pumps of choice for circulating water at limited heads, due to their high efficiency and versatile modular automation options. The pump can be dimensioned for you in order to achieve the lowest possible energy consumption, thereby reducing the payback period. In addition, it can be

ISO2858 standardized pumps for the chemical industry Applications: Suction of clean or slightly turbid, hot, overheated, acidic or basic liquids in the chemical, petrochemical, pharmaceutical, food, paper, wine, steel, textile industries, etc. – Flow up to 500 m³/h and pressure up to 16 bar, – Wide range of materials (from cast iron to Hastelloy), –

Applications : Clean, non-abrasive liquids and liquefied gases – The TBH and TBA series pumps are suitable for handling clean, corrosive, hot or cold liquids in the chemical, petrochemical, pharmaceutical, food and beverage industries. – Removal of condensate and distilled liquids, – Solvent and liquefied gas applications, – Boiler feed, – Extraction or liquid from

Applications: – High temperature circulator – Frying oil – Edible vegetable oils – Ideal for thermal oils up to 320 C and thermal food oils, – Non-thermal oil bearing, for greater safety, – High temperature transfer without cooling, – Compatible with most Allweiler NTT pumps, – No need for pump cooling system, – Better heat

Travaini TRVX – single-stage liquid ring vacuum pump up to 2000 m³/h at 33 mbar vacuum This innovative design liquid ring vacuum pump creates vacuum in only one stage, and is designed to be light, compact, durable and to have a very good service life. – Energy consumption 10% lower than traditionnal design – Service

Travaini TRMX – compact single-stage liquid ring vacuum pump up to 95 m³/h at 33 mbar vacuum This innovative design liquid ring vacuum pump creates vacuum in only one stage, and is designed to be light, compact, durable and to have a very good service life. – Energy consumption 10% lower than traditionnal design –

Travaini TRH and TRS pumps are capable of handling large volumes of air, vapors and condensates. Strengths: pure air discharge; various possibilities of esrvice liquids (water, oil, solvents); pressure up to 33 mbar (abs); very reliable and easy to maintain; large choice of materials; large stock and fast reaction time. Advantages: unmatched reliability, making them

For handling corrosive fluids. Applications: water treatments, aquarium, cosmetic industry, chemical laboratories, corrosive chemical solutions, toxic liquid, sea water, pure water, chemicals te preserve food… – Construction : mag-driven centrifugal, horizontal axis, close-coupled types, the pump casings are entirely built with reinforced thermoplastic, – Versatility : you can practically pump all the chemicals at low

Argal Hippo is a full plastic self-priming centrifugal pump ideal for loading or unloading (waste-)chemicals from trucks, tanks or vessels, due to it’s capacity to dry run and to handle particles as well as priming capability. The pump can handle high specific weights and vapor pressures by it’s design. Benefits: * Can run dry (ideal

The Argal Rhino is a full plastic self priming pump with biphasic impeller for moderate flows – solid laden, degassing fluids, high vapour pressure fluids or higher densities possible by it’s impeller design. The combination of its self priming and pumping degassing media capacities, make this pump an ideal pump to use in filtration applications

The Argal ELK is a full plastic self priming pump for smaller flows – solid laden, degassing fluids, high vapour pressure fluids or higher densities are possible by it’s peripheral impeller design. The combination of its bi-directionality and self priming and degassing media capacities, make this pump an ideal pump to use in filtration applications

Submersible pumps for water treatment or scrubber applications. – ideal for liquids containing solids, – Indoor or outdoor installation, – dry steam seal, – easy assembly and IEC motor alignment. The pumps in this original Argal product are made of thermoplastic techno-polymers; they are close-coupled, vertical-axis, with a downward-facing axial hydraulic suction connection and a

One-piece radial flow centrifugal pump ISO 2858 Industrial applications requiring temperatures from -40 C to 120 C. For chemicals, acids and solvents. in: Water and wastewater treatment; Chemical and pharmaceutical processes; Scrubbers; Cooling towers; Pickling processes; Electroplating processes. – Resistant to most chemicals – Sealed pump or magnetic drive – High reliability due to simple

Extremely durable and suitable for harsh, even critical environments and applications. Applications: Salt water, bilge water, seawater, concentrated brine; Abrasive liquids, Ti O2, ashes; Bleaching solution, hydrogen peroxide, bleach; Hydrofluoric acid. – For fluid circuits that do not offer a very high NPSH, – ATEX – Pump body made of glass fiber reinforced resin, –